• Operates off cold mains water supply.
• Heats water as it is used.
• Simple to use single on/off and temperature control.
• 3kW.
• Compact design.
• 200mm swivel arm.
• Open outlet.
• Thermal limiter set at 55°C +/- 3°C..
• Minimum supply water pressure/1bar running.
• Maximum supply water pressure 10bar static.

Autosensor is a unique hand wash unit operated by a no-touch sensor activating the water supply aiding hygiene where cross-contamination must be avoided. Autosensor is the ideal product in locations from Hospitals to food preparation areas. The unit is fitted with a patented non-scaling vortex spray outlet which eliminates the need for costly maintenance. It even has an automatic shut off to eliminate water waste.

For use with HH19

7 litre capacity, point of use
Adjustable thermostat 15°C - 75°C with frost protection setting
300mm swivel spout included. Extended outlets available (DX107)
Wall bracket and full fixing pack supplied
Integral safety over temperature thermal fuse
3 year guarantee (UK)

 

Can be mounted undersink using the special monoblock chrome-mixer accessory (DX108).  

Extended swivel Spouts for use with DX106. 450mm or 600m

Monoblock Vented Chrome Mixer for use with DX106 

The vented heater connects directly to the cold water supply and provides hot water to a single outlet. There is no need for an expansion vessel or relief valve. It has a frost protection setting to protect the heater when not in use and a manually resettable over-temperature safety cut-out. It has an externally adjustable temperature control and a neon light indicates when the heating element is “on”.

Connection: to cold water mains.
Temperature control: adjustable from 35 -80ªC.  Thermostat: capillary type

Heating element: embedded rod type. Rating: 2.0 kW

Water tank: approved polypropylene tested to 300 kpa. Case: impact resistant plastic

Insulation: contoured polyurethane, CFC free. Safety feature: manually re-settable over-temperature safety cut-out

Multipoint mains pressure instantaneous water heater ideal for undersink mounting or where space is at a premium.

• 9.5 kW power rating (requires single phase electricity supply)
• Water supplied to one or two outlets
• Water outlet via existing tap or mixer (especially suitable via spray tap)
• Plumbs directly into cold water mains
• Small compact shape
• No standing heat losses
• Fast response
• Three heat settings
• Dimensions H190mm x L305mm x D120mm

Up to two outlets. Powerstream. In shower applications use NS285. Recommended Cable Size: 10mm Twin and earth with 40 amp fuse. Dimensions: 160mm(h) x 307mm(w) x 74mm(d)

• Suitable for Office, Workshops and Factories. Size 450mm x 360mm x 200mm 
• 2.0kW element for rapid heat up. external temperature control
• neon element-on indicator. glass-lined vessel with magnesium anode 
• manually re-settable thermal cut-out
• wall mounting or floor standing option.  pressure relief valve included
• 10L suitable for 1 to 2 sinks, 15L suitable for 2 to 3 sinks depending on simultaneous usage

Mains pressure (unvented) unit - maximum working pressure 6 bar. Maximum working temperature 75 degrees Centigrade

The supplied pressure relief valve must be fitted in every case. Depending on the details of the installation, additional accessories may be needed to comply with the Water Regulations. If your nearest cold water draw off is close to the heater, you will need to fit a check valve and expansion vessel. If your mains water pressure is above 4.2 bar, you will need to fit a pressure reducing valve

2kW

Use: 10 Litre = 2 to 3 Basins.   15 Litre = 4 to 5 Basins.

Max. temperature 80°C.

17 minute reheat/26 minute for 15 litre

Unvented cold water feed.

Extra thick steel-plated tank, pressure tested and double coated vitreous enamelled. Large magnesium anode.

CFC free polyurethane thermal insulation.

Regulation thermostat equipped with safety thermostat.

3 year tank guarantee (1 year guarantee on electrical components).

15 litre version also has External temperature control and heating indicator light.

Dimensions: W350mm x H203mm x D300mm

• Will deliver hot water to as many as four outlets
• Balanced supply of hot and cold water
• Heat loss minimisation and energy savings from short pipe runs and superior insulation
• Water outlet via existing tap or mixer
• Adjustable thermostat to 70 deg C. at 3KW rating
• Over temperature safety cut-out
• Temperature and pressure relief valve factory fitted to all MW models and available as accessory for EW range
• Neon light indicates when heater is working
• 10 Lites = 3 basins, 15 Litres = 4 basins
• Compact shape for undersink mounting
• Remote siting possible
• The EW/MW range has been designed to provide stored hot water from a mains pressurised water supply.
• The EW range has been designed without the need for the temperature and pressure relief device making installtion even simpler. 

• Size: 360mm x 360mm x D254mm

Aquapoint lI delivers hot water for one or more outlets. It has a glass lined steel storage tank tested to 12 bar. A sacrificial anode is fitted for protection against aggressive water conditions.  The Aquapoint II has a factory fitted P&T socket and external temperature control with frost protection. 

5ltr - Power 2.2kW | Dimensions 376 x 256 x 260mm (H x W x D)

Thermostat: capillary type adjustable up to 20ºC to 75ºC.  Water tank: 1.8 mm glass enamelled steel with a working pressure of 6 bar.  Case: high impact resistant white plastic. Insulation: high density, CFC-free polyurethane foam

10ltr - Power 2kW | Dimensions 460 x 350 x 265mm (H x W x D)

15ltr - Power 2kW | Dimensions 460 x 350 x 310mm (H x W x D)

Direct unvented multipoint.  Thermostat: Adjustable 7ºC to 75ºC. Thermal cut-out: Manually re-settable set to 85±3ºC

Safety Features: Expansion relief valve set to 6 bar (supplied).  Manually re-settable over temperature safety cut-out

Heat up time: 10ltr - (15° to 65ºC) 18 mins                              15ltr - 32 mins

Re-heat time: 10ltr - (70% vol.)     12 mins                              15ltr - 18 mins

Hotflo can service up to three basins and incorporates a copper inner container, requiring no anode, to achieve optimum performance in terms of durability and corrosion resistance. 

• U1  Pressure Limiter
• U2 Expansion vessel, Expansion and check valves
• U3 Blending valve
• U5 Expansion vessel
• U6 Temperature and pressure relief valve
• U7 TMV3 Themostaic blending valve

Loading: 3kW/230v~.  Fuse Rating: 15A

Thermostat: Adjustable 25ºC to 75ºC.  Thermal cut-out: Manually re-settable set to 84+0/-5ºC

Water vessel: Glass enamelled steel tested to 13 bar. Maximum working pressure 6 bar

Insulation: High performance foam insulation

Controls: Pressure reducing valve and line strainer set to 3.5 bar.  Expansion relief and single check valve set to 6 bar

Pressure and temperature relief valve set to 7 bar and 90ºC.  External expansion vessel pre-charged to 3.5 bar

Expansion vessel capacity: 5 litre.  Complete with all the necessary accessories and factory fitted P&T valve.

30ltr Dimensions 420 x 525 x 445 mm (H x W x D).

50ltr Dimensions 690 x 500 x 512mm (H x W x D)

80ltr Dimensions 950 x 500 x 512mm (H x W x D)

100ltr Dimensions 1125 x 500 x 512mm (H x W x D)

Two adjustable thermostats for precise control. Overheat protection. Ideal for replacement (overflow and cold feed can be connected on the left or right hand side). 50 to 80degC thermostatic control range. Constructed with copper sheet water vessel with brazed seams, corrosion proofed seal with enamel finish outer casing. 3kW Incaloy sheathed element.  

CT25 Cistern Type 25 Water Heater

Capacity: 25 Litres (hot) and 8 Litres (cold)

Dimensions: 705mm(h) x 470mm(w) x 210mm(d) Weight: 20kg (53kg full)

CT50 Cistern Type 50 Water Heater

Capacity: 50 Litres (hot) and 24 Litres (cold)

Dimensions: 750mm(h) x 600mm(w) x 320mm(d) Weight: 32kg (106kg full)

CT75 Cistern Type 75 Water Heater

Capacity: 75 Litres (hot) and 24 Litres (cold)

Dimensions: 925mm(h) x 600mm(w) x 320mm(d) Weight: 37kg (136kg full)

CT100 Cistern Type 100 Water Heater

Capacity: 100 Litres (hot) and 24 Litres (cold)

Dimensions: 1080mm(h) x 600mm(w) x 320mm(d) Weight: 40kg (164kg full)

* TWO YEAR WARRANTY (UK) ONLY *

The LWSS stainless steel range of water heating cylinders provides effective, fast and safe mains-fed hot water around any property. A high quality vessel employing the best in laser welding technology, the LWSS range features high flow rates, energy efficient insulation and an expansion vessel. A high quality vessel employing the best in laser welding technology, the LWSS range features fast flow rates, energy efficient insulation and an expansion vessel to prevent wasted water.

Ideal for apartments needing Mira showers or similiar where the hot water pressure will be low

·          Duplex stainless steel water heating cylinder – for maximum strength and long life

·          Pressure tested to 15 bar

·          Provides effective, fast and safe mains-fed hot water

·          Two long life incoloy, low noise immersion heaters

·          Easy to install with simple step by step installation guide

·          Energy efficient rigid polyurethane foam insulation (CFC/HCFC free)

·          Relief valve operates at 7 bar / 90-95°C

·          3 bar working pressure

·          High flow rates of up to 55 litres per minute

·          Minimum recommended supply of 1.5 bar with flow rate of 25 litres per minute

·          22mm cold feed

·          Wipe clean, corrosion resistant, white coated steel case

·          25 year cylinder guarantee

·          90ltr 750x510mm

Megalife is a range of ten large-capacity (100-210 litre) indirect (Including separate coil) or directly heated, vented water heaters. 3kw power. It is suitable for a wide range of commercial and light industrial applications where a bulk supply of hot water is required for washing, showering and other needs. Typical applications include canteens, offices, schools, colleges, small hotels, nursing homes, sports clubs and light industrial premises.

• Transferable 25-year cylinder guarantee
• Internal air-gap with unique floating baffle
• No sacrificial anode (eliminates annual inspection)
• 3 bar operating pressure
• High performance 'coil in coil' heat exchanger
• improved insulation for maximum heat retention
• Every unit tested to 15 bar (217psi)
• 1/2" temperature and pressure relief valve